NEWARE EV Module Diagnostics & Testing:
High Performance, Cell Status, CAN, Operating Envelope

NEWARE’s EV Module Tester delivers lab-grade diagnostics for battery modules: capacity, SOC/SOH, DCIR/HPPC power, CAN BMS data, and Operating Envelope checks. Kelvin 4-wire, ±0.02% FS V / ±0.05% FS , 100 Hz logging, and ~10 ms response capture fast transients. Regenerative discharge (~90% eff.) and auto reports enable safe, repeatable, standards-aligned testing.

 
EV Pack Diagnostics Flow — PACK → MODULE → CELL Find the fault fast: localize at pack, isolate at module, verify at cell PACK / System-Level Checks MODULE / Isolation & Triage CELL / Testing & Evaluation You are here PACK Diagnostics & Fault Localization OCV/SOC/SOH · DCIR/HPPC · Insulation/HVIL CAN DTC → Flag suspect module(s) Visit this page You are here MODULE Isolation & Triage ΔV/ΔIR scan · Balance state · Thermal check CAN (BMU) → Pinpoint bad cell group You are here CELL Testing & Evaluation OCV/SOC · DCIR · Capacity/Efficiency Self-discharge → Root cause / Grading Visit this page

High Performance: 0.05% FS & 100Hz

NEWARE Battery Module Tester is a high-precision, bidirectional charge/discharge system purpose-built for high-power EV battery modules. It delivers fast dynamic response, stable accuracy, and flexible multi-channel configurations for core use cases: pulse testing, cycle-life testing, and drive-profile (duty-cycle) simulation.
With regenerative energy recovery and multi-channel inputs, it cuts test energy consumption and thermal load. The platform uses a bidirectional high-frequency DC conversion topology and multi-channel 24-bit ADCs to achieve 0.05% FS current accuracy, 100 Hz data-sampling rate, and ≈10 ms current response time—providing higher resolution and tighter control than conventional single-range instruments. This makes it ideal for EV module diagnostics, characterization, and validation.

NEWARE Module Tester Baseline Specifications
Parameter Data Notes
Voltage Accuracy 0.02% of FS Measurement accuracy for pack voltage.
Current Accuracy 0.05% of FS Measurement and output accuracy for charge/discharge current under rated range.
Power Factor ≥ 99% (Full Loads) At nominal power during regenerative operation to the grid.
THDi ≤ 5% (Full Loads) Total Harmonic Distortion of input current during regeneration (per IEC/GB limits).
System Efficiency (Max) 90% End-to-end discharge-to-grid efficiency at rated power.
Current Response Time ≤ 10ms Rise/settling time for step current commands.
Input Impedance ≥ 10MΩ High input impedance (low leakage) for precise voltage sensing.
Sampling Rate 100 Hz Data acquisition frequency for logging and control
Notes: Some specifications vary by model; please refer to the model-specific datasheet.

Typical Module Solution Example

NiMH Module
(6S, 7.2V, 6.5Ah)

✔ CE-4008-10V10A-SR

Li-on Module
(74S6P, 25V, 233Ah)

✔ CE-6004n-60V300A-H

LMO Module
(2S2P, 7.6V, 60Ah)

✔ CE-6008n-20V120A-H

Other Module
(?)

Module platform based

Module Diagnostics (Capacity, SOC, SOH, DCIR)

  • Capacity — lab grade accuracy
  • Precision measurement chain + high input impedance (low leakage) for exact coulomb counting
  • Fully programmable charge/discharge profiles to simulate real duty cycles
  • Repeatable cycle-life capacity tests with consistent results
  • SOC — automatic & aligned
  • Auto-calculated during the run (coulomb counting + OCV alignment)
  • SOH — capacity & impedance in one view
  • Auto computation from measured capacity and resistance trends
  • Clear pass/fail and historical comparison in the same report
  • DCIR — fast, clean pulse measurements
  • 100 Hz sampling captures transients reliably
  • <10 ms current response for crisp ΔV/ΔI results

Module-Level Cell Consistency

Module doesn’t have BMS?

Use the built-in Aux Unit on the module tester to monitor each cell in real time with high accuracy—capturing detailed status and pinpointing faulty cells.

Operating Envelope Simulation

Neware’s new Operating Window enables full-pack operating envelope validation and simulation without the vehicle BMS. Define limits across SOC and temperature, apply dynamic lookups, and reproduce real-world charge/discharge limits to measure an EV battery pack’s true performance under varying conditions—ideal for rapid calibration, strategy verification, and limit testing.

Up to 3-D Matrix can be loaded into the system to produce dynamic values, and the tester updates output current/power in real time based on the lookup results.

Discharge Energy Regenerative

NEWARE module testers feature regenerative discharge (up to 90% efficiency), returning discharged energy back to the grid to minimize waste. By avoiding resistive heat dumping, regeneration cuts thermal load, which reduces lab HVAC burden, prevents hot spots and thermal drift, lowers fan noise and wear, and mitigates temperature-induced derating or safety risks during long tests. The result is cleaner energy usage, steadier test conditions, and longer equipment life.

Regenerative Discharge — Battery → Tester → Grid DC energy is converted and fed back to the grid DC Discharge DC → AC Conversion AC Feed-in Battery (DC) NEWARE Tester (Bidirectional) DC Link DC → AC η ≈ 94% Power Grid (AC)

Get Expert Solutions and Quotes

Submit your request and we will respond within 2 business hours.